9 English reviews written for 3DJAKE ASA Black
66 customer reviews in all languages
| 5 stars | | 92 | (70%) |
|---|---|---|---|
| 4 stars | | 24 | (18%) |
| 3 stars | | 10 | (7%) |
| 2 stars | | 2 | (1%) |
| 1 Stars | | 3 | (2%) |
Filter reviews:
-
Raz
11 June 2026
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Was this rating helpful? (0) (0)
-
ScottP
28 March 2026
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
A good colour match for Filamentum ASA Traffic Black.
I bought this to match the colour of my existing printed parts.
prints slightly cooler and much easier to print than ABSWas this rating helpful? (0) (0)
-
TheMinjus
15 May 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
Super adhesion on bed
Love it, just print it on 110c heatbed, fans 40-70%
Was this rating helpful? (1) (0)
-
Rated with 3 out of 5 stars.
3D Jake ASA
Warps more than other brands of ASA. I need to print it very hot to avoid warping issues, even on small parts: 260 degrees nozzle and 110 degrees bed (which is outside the recommended parameters).
I print in an enclosure which I heat up before printing to ~35 degrees, but even then I get severe warping at 255 degrees nozzle and 100 degrees bed.Was this rating helpful? (8) (0)
-
Wouter
09 November 2023
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 3 out of 5 stars.
3DJake ASA black
Material prints very nice and looks beautiful. But the deeper the spool gets the more knots. I was able to save a few prints when i was around the printer. But had a few prints fail when i was not around. Ill try to rewind the spool, hope i can fix this issue with this.
Was this rating helpful? (3) (0)
-
Jimmers
24 May 2023
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
Love this stuff
I've only printed one spool but any time I need to print something functional this comes out - Magnetic handle for my telescope? Fusion360, some of this ASA, 5 hours later, perfect. Bespoke ramp over a door frame? 22 hours later, perfect ramp! No warping if I'm not lazy and looks great to boot.
Was this rating helpful? (0) (0)
-
Oleg
19 November 2022
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 5 out of 5 stars.
This is now my go-to material.
Prints surprisingly good, with good adhesion, stiffness and low warping.
Can even print decorative things on minimal cooling and hotend temperatures typical to PLA, only at the cost of layer adhesion.Was this rating helpful? (1) (1)
-
Rated with 3 out of 5 stars.
Weak properties
This Asa filament (Light Grey) has very nice prints, smooth, no stringing, in my opinion more than suitable for design print even without need of aceton smoothing. But it is very soft to use for any technical appliance that needs strenght, compared to any other ASA or ABS brands. I'll keep it just for print Ing figures and stuff like that but thats's it.
Was this rating helpful? (1) (0)
-
Adam
12 May 2020
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Rated with 1 out of 5 stars.
No good
This ASA is the worst Ive ever used. It was extremely prone to warping and splitting. I tried removing moisture more than once in a convection oven with no improvements. In addition the spool it came on had a triangular centre and not round which makes it very hard to avoid tangles because the spool jumps when turning. When the spool is 2.3kg its not practical to put the roll on bearings.
Was this rating helpful? (6) (1)
Magazine Articles:
- How to use the fuzzy skin feature in Cura
- Improving Small Text in 3D Printing: Achieve perfectly clear & legible text at last!
- YouTube Episode: The Elegoo Centauri Carbon 2 - A Carbon Copy?
- Mesh Booleans in 3D Printing: Cut, Combine & Customise Models Without CAD!
- PrintaFix Basic - Warp-free Printing Results
Discover 3DJake:
-
Switzerland: Free standard delivery from CHF 69.90
-
Delivery in 3 business days.
More than 11.050 products
We deliver worldwide to
more than 40 countries
Rated with 3 out of 5 stars.
Oversized spool, decent filament.
The filament itself is alright, but the spool is too big to fit in a Bambu AMS 2 Pro and does not rotate freely.